U0006 High Speed CAN Communication Bus (-) Open Circuit

U0006 High Speed CAN Communication Bus (-) Open Circuit is a diagnostic trouble code that indicates the vehicle's High Speed CAN (Controller Area Network) communication system has detected an open circuit on the CAN Low (-) communication line.

The CAN network is the electronic communication system that allows different control modules in modern vehicles to exchange information. High Speed CAN is used for systems that require fast and reliable communication, including the engine control module, transmission control module, ABS system, stability control modules, and other powertrain-related electronics.

Under normal operating conditions, the CAN Low (-) wire provides a continuous communication path between connected control modules. If this wire is broken, disconnected, damaged, or has a poor electrical connection, communication between modules may become unstable or completely interrupted.

When a control module detects that the High Speed CAN Low circuit is open, it stores the U0006 fault code.

This fault is commonly caused by broken CAN wiring, damaged connectors, corrosion, loose terminals, water intrusion, faulty control module connections, or incorrect electrical repairs.

What Does U0006 High Speed CAN Communication Bus (-) Open Circuit Mean?

The High Speed CAN communication system uses two wires:

• CAN High (+)

• CAN Low (-)

These two communication lines transmit digital information between electronic control modules.

The CAN Low wire must maintain a complete electrical connection for proper communication.

An open circuit means that the electrical path has been interrupted.

Possible causes include:

• Broken CAN Low wire

• Disconnected connector

• Damaged wiring harness

• Corroded terminals

• Loose electrical connections

• Faulty control module connection

What Is the High Speed CAN Bus?

Modern vehicles use multiple CAN networks designed for different communication requirements.

The High Speed CAN bus is designed for systems that require rapid data exchange and accurate information transfer.

It commonly connects modules such as:

• Engine control module (ECM)

• Transmission control module (TCM)

• ABS control module

• Stability control module

• Electric power steering module

• Advanced driver assistance systems (ADAS)

The exact modules connected to the High Speed CAN network depend on vehicle design and manufacturer.

How Does the CAN Communication System Work?

The CAN system allows multiple electronic modules to communicate through a shared two-wire network.

Examples of CAN communication include:

• Engine module sharing engine speed information

• ABS module sending wheel speed data

• Transmission module receiving operating information

• Stability control system exchanging vehicle movement data

Each control module sends and receives digital messages through the CAN bus.

If the CAN Low line is open, communication messages cannot be transmitted correctly between modules.

Symptoms of U0006

Symptoms depend on which modules lose communication and the severity of the fault.

Check Engine Light and Warning Lights

The vehicle may display:

• Check Engine Light

• ABS warning light

• Airbag warning light

• Stability control warning

• Transmission warning light

Multiple Communication Fault Codes

A common symptom is several U-series codes appearing at the same time.

Possible codes include:

• Lost communication codes

• CAN voltage faults

• Network performance faults

Engine Performance Problems

Because High Speed CAN connects powertrain modules, possible symptoms include:

• Reduced engine power

• Poor throttle response

• Limited engine operation

Transmission Problems

Possible symptoms include:

• Harsh shifting

• Delayed gear changes

• Transmission warning messages

• Limp mode operation

Starting Problems

If important modules cannot communicate, possible issues include:

• No-start condition

• Immobilizer communication problems

• Delayed starting

Electronic System Failures

Drivers may notice:

• Incorrect dashboard information

• Random warning messages

• Electronic systems working intermittently

Common Causes of U0006

Several problems can cause an open circuit on the CAN Low communication line.

Broken CAN Low Wiring

Physical damage to the communication wire is one of the most common causes.

Possible issues include:

• Broken wires inside the harness

• Cut wiring

• Wiring damaged during repairs

• Harness rubbing against metal components

Damaged Connectors

Connector problems may interrupt CAN communication.

Possible causes include:

• Loose terminals

• Broken pins

• Poor electrical contact

• Connector separation

Corroded Electrical Connections

Corrosion can prevent proper CAN communication.

Common causes include:

• Moisture exposure

• Water leaks

• Poor connector sealing

• Oxidized terminals

Water Damage

Water entering electrical components may cause:

• Open circuits

• Connector corrosion

• Communication failures

Common affected areas include:

• Engine compartment connectors

• Fuse boxes

• Control module housings

• Interior wiring areas

Faulty Control Module

A damaged module or poor module connection may interrupt the CAN Low circuit.

Possible affected modules include:

• Engine control module

• Transmission control module

• ABS module

• Body control module

• Steering control module

Incorrect Electrical Repairs

Previous electrical work may create CAN communication problems.

Examples include:

• Incorrect wire splicing

• Damaged harness repairs

• Incorrect connector installation

Aftermarket Electrical Equipment

Improperly installed accessories may damage or interrupt CAN wiring.

Examples include:

• Alarm systems

• Remote starters

• Multimedia systems

• Tracking devices

How Is U0006 Diagnosed?

Proper diagnosis requires checking the High Speed CAN network, wiring, and connected modules.

Check for Additional Fault Codes

A diagnostic scan should identify:

• Other U-series codes

• Modules that cannot communicate

• Network-related problems

Additional codes help locate the affected area.

Check CAN Bus Resistance

Technicians measure:

• Resistance between CAN High and CAN Low

• Circuit continuity

• Network integrity

Incorrect readings may indicate an open circuit.

Inspect CAN Wiring

The wiring harness should be checked for:

• Broken wires

• Damaged insulation

• Previous repairs

• Physical damage

Inspect Connectors

Electrical connectors should be checked for:

• Corrosion

• Water damage

• Bent pins

• Loose terminals

Test Module Communication

Technicians may check each control module to determine which part of the network has lost communication.

Disconnect Modules if Necessary

Individual modules may be disconnected to determine whether a faulty module or connection is causing the open circuit.

How Is U0006 Fixed?

The repair depends on the actual cause of the CAN communication fault.

Repair CAN Wiring

Possible repairs include:

• Repair broken CAN Low wires

• Replace damaged wiring sections

• Restore proper insulation

Repair or Replace Connectors

Repairs may include:

• Cleaning corrosion

• Repairing terminals

• Replacing damaged connectors

Repair Module Connections

Loose or damaged control module connections should be corrected.

Replace Faulty Control Modules

If a module is internally causing communication interruption, replacement may be required.

Repair Water Damage

Any moisture source should be corrected to prevent future communication problems.

Remove Incorrect Aftermarket Equipment

Improper electrical installations may need repair or removal.

After repairs:

1. Clear all fault codes.

2. Verify communication between modules.

3. Check High Speed CAN network operation.

4. Perform a road test.

5. Confirm that U0006 does not return.

Can You Drive With U0006?

Driving with U0006 may be possible in some situations, but it depends on which systems are affected.

Possible risks include:

• Loss of communication between safety systems

• ABS or stability control problems

• Transmission issues

• Starting difficulties

• Unexpected electronic failures

If multiple warning lights appear or important vehicle systems are not operating correctly, the vehicle should be inspected promptly.

Is U0006 a Serious Code?

U0006 is generally considered a serious communication system fault.

A High Speed CAN open circuit can prevent important vehicle modules from communicating properly. Since modern vehicles depend heavily on electronic communication networks, this fault can affect safety, performance, and reliability.

Prompt diagnosis is recommended.

How to Prevent U0006

Regular electrical maintenance can help prevent CAN communication faults.

Protect Wiring Harnesses

Avoid:

• Damaging wiring during repairs

• Incorrect electrical modifications

• Poor cable routing

Keep Connectors Clean and Dry

Prevent:

• Water intrusion

• Corrosion

• Loose electrical connections

Install Accessories Correctly

Aftermarket electronic equipment should be installed properly to avoid CAN network problems.

Maintain Battery and Charging System

Stable electrical operation helps protect vehicle communication systems.

Repair Electrical Problems Early

Small wiring problems can develop into major CAN communication failures.

Final Thoughts

U0006 High Speed CAN Communication Bus (-) Open Circuit indicates that the vehicle has detected an interruption in the CAN Low communication circuit.

The most common causes include:

• Broken CAN Low wiring

• Damaged connectors

• Corrosion

• Water damage

• Faulty control module connections

• Incorrect electrical repairs

• Aftermarket equipment interference

A complete inspection of the High Speed CAN network, wiring harnesses, connectors, and control modules is required to restore reliable communication between vehicle systems.